Highlights
of our
Machine
• Our machines are warranted for three years. Except for wear parts,
bearing, and rubber parts.
• Our machines can take feed size from zero to 100 mm model wise.
The size feed increases capacity wise. for smallest model of
sand making machine is 12 mm and is up to 100 mm for
VSI having capacity of 200 tph. The most economical feed size
for crushing is 1:3 ratio. For manufacturing sand most
economical feed size reccomnded is all metal passed from 12 mm
square mesh size (longest length up to 16 mm.)
Feeding 0 to 12 mm all mixed to sand machine gives much better sand.
• Sand of any F.M. specification, or zone can be
manufactured by changing the sieves of the vibrating screen.
• Our VSI machine can be used for mostly all industrial
minerals and recycling waste.The wear cost may be different for
material to material. Wear is a factor of Hardness of the stone,
feed size and abbresive quality of the material.
Proven Application on:
1) Aggregates and sand from all types of stones, Basalts,
Dolomite, Flint,Gabbros, Gravels, Grit stone, Lime stone,
Phosphate, Pumice, Quartz Jasperoid, Quartzite, Sand stone,
Silt stone etc
2) Industrial Minerals:
Quality sand, Ceramics, Abrasives, Cement Clinkers, Glass,
Silica, Manganese ore, Iron ore etc
3) Waste and recycleing:
Glass, Steel slag, Construction Waste etc
• Now, we supply the machine with our New
Wear resistance Rotor (Patented) which gives
long life. the wear cost is very less. The life of the rotor is very long
( upto 5000 hours depends upon material)
• Our machines are oil lubricated with forces
circulation, the heat of the oil is extracted in
heat exchanger. The machine can run round the
clock with out any interruption. More efficient than
grease lubrication.
• A separate sheet is attached for comparison
of Grease Lubrication Vs. Oil Lubrication.
Oil lubrication saves about Rs115000 per year.
• The surface texture of the sand particle,
is very good.
• Our Machines are much sturdy and strong in
construction.
• For Making sand (3.2 To 3.8 F.M.) we assure
capacity of our machine Plus or minus 10%
• A classifyer ( air washing) can be fitted in series
to separate extra Dust in sand if required.
• We can supply complete plant, portable Plants on
trolley.
• The rotating mechanism and other body are
separated by anti vibration padding, no vibrations
are transferred to structure.
• The rotor which is a main part of the
machine, is designed on super flow principle,
which gives the obstruction free flow of
material, reduces wear cost to a substantial.
• Our machines gives consistance Gradation regardeless
of the condition of wear parts.
• Damp material having moisture up to 4% can be
crushed with any clogging.
• A special internal air curculation System of V.S.I. makes
it dust free in operation.
• While crushing fine ( sand) dust may be emited from
out let, and can be supressed by spraying water at out let.
• Our machine have very low noise level not more than 70 Db at 10 mtrs.
•The estimated life of the bearing is about 50,000 hours working with
proper lubrication system.Any abusive lubrication system, operating with
Excessive vibration may reduce the life of bearing. No gaurantee regarding
bearing life is given.
• No tramp iron should enter in the machine. The Wear parts are very hard,
and may get broken due to tramp iron. It is strongly recommended to install a
magetic separator at the feeding end to the machine.
• The bearing cartage is oil lubricated by forced oil pumping.
The ultra 10 W oil of Servo make is recommended.Change the oil after every
1500 hours working or when the oil looses it's viscocity which ever is earlier.
• The VSI crusher is driven by Vee belts. Proper belt tension is very important.
Loose or very tight belts may affect the capacity of the machine.
• Every machine is supplied with maintenence and operation manual. Before
operation, it must be read and all instructions must be followed strictly.
|
